WHS Documents for Tilers
Site-specific, delivered in about 4 minutes · free revision within 24h if your builder asks for changes
Tilers on an Australian construction site need a core WHS document set built around the SWMS: a site-specific Safe Work Method Statement for each high risk activity, a SWMS register, current licences, Safety Data Sheets, and induction and sign-on records. Which SWMS you need is driven by the high risk construction work a tiler does: silica dust from tile cutting and grinding, falls from balconies and stair voids, adhesive and epoxy exposure.
The core WHS documents a tiler needs
- ✓ Site-specific SWMS covering each high risk activity (legally required under your state's WHS Regulations, provision 299)
- ✓ A SWMS register indexing every document, version and review date
- ✓ High risk work licences and tiler trade licences
- ✓ Safety Data Sheets for hazardous chemicals, and a chemical register
- ✓ Site induction record and daily sign-on / SWMS acknowledgement sheets
The SWMS a tiler usually needs
A SWMS must cover each of these high risk construction work activities before the work starts. The Trade SWMS Pack generates one for each, site-specific to your job:
- ✓ Tile cutting and grinding with silica dust controls
- ✓ Bathroom and wet area tiling with waterproofing membranes
- ✓ Balcony and external tiling above 2 m
- ✓ Floor grinding and surface preparation
- ✓ Stairwell and void-edge tiling
- ✓ Large format tile handling and installation
The high risk construction work that triggers a tiler's SWMS
A SWMS is legally required because tilers routinely do this high risk construction work:
- ✓ Risk of a person falling more than 2 metres
See all 18 high risk construction work categories and how they map to your work.
Same documents, different state citations
A tiler in NSW and one in Victoria need the same documents, but each SWMS must cite the right law: the harmonised WHS Regulations in seven jurisdictions, or the OHS Regulations 2017 in Victoria. See the full SWMS requirements by state, or open the tiler WHS documents page for your state:
Tiler WHS documents NSWTiler WHS documents VICTiler WHS documents QLDTiler WHS documents WATiler WHS documents SATiler WHS documents TASTiler WHS documents ACTTiler WHS documents NT
Common questions
▸What WHS documents does a tiler need on site?
At minimum, site-specific SWMS covering every high risk activity you perform (one SWMS can cover several activities), a SWMS register, your high risk work and trade licences, Safety Data Sheets for any hazardous chemicals, and proof of induction. The SWMS is the legally required one and the one a principal contractor checks first.
▸How many SWMS does a tiler need?
Every high risk construction work activity you do must be covered, which for tilers is usually the 6 activities listed above. One SWMS can legally cover several activities, but most trades keep one per activity because that is how builders review them. The Trade SWMS Pack generates all of them from one questionnaire for A$179.
▸Do tilers need different documents in different states?
The documents are the same; the legislation they cite differs. Seven jurisdictions use the harmonised WHS Regulations (provision 299 for the SWMS duty; NSW's WHS Regulation 2025 cites it as s 299); Victoria uses its OHS Regulations 2017. A SWMS should be re-cited and re-reviewed before it is used in another state.
Every SWMS a tiler needs, in one go
The Trade SWMS Pack generates all 6 SWMS above from a single questionnaire, plus the register, toolbox talks and sign-on sheets, for A$179.
See the Trade SWMS PackKeep exploring
SWMS for tilersWHS documents by trade (all)Trade SWMS PackFree SWMS templateElectrician WHS documentsPlumber WHS documentsCarpenter WHS documentsRoofer WHS documentsScaffolder WHS documentsConcreter WHS documents